Controval
Product group

Control and automation

Our own engineers design the control system, build the panel and commission it on your site. One team covers the logic, the hardware and the startup.

At a glance

We design, program, build and commission the control systems that run your equipment and skids.

  • PLC, remote I/O, HMI and SCADA design and programming
  • DCS and SIS migrations, including PVCII
  • Pneumatic, electric, hydraulic and PLC panels designed and built by Controval
  • Panels commissioned in the field and supported after startup
01

Industrial automation

Industrial automation is the hardware and programming that lets a process run, alarm and report with little manual action. A good design is simple to operate, clear to troubleshoot and easy to expand.

Request a quote
Control room with SCADA screens

PLC

A programmable logic controller reads inputs, runs the program in fast cycles and drives outputs. It suits machines, skids and packages. Selection depends on I/O count, speed, redundancy, communications and the hazardous area rating of the location.

Remote I/O

Remote I/O modules sit near the field devices and send signals to the controller over a network. They cut cable runs and wiring cost on spread-out plants. The network becomes a single point to protect, so layout and redundancy matter.

HMI

The human machine interface shows the operator status, alarms, trends and set points, locally on a panel screen. A clear screen design and a sensible alarm list matter more than the amount of data shown.

SCADA

Supervisory software collects data from many controllers, shows it centrally, stores history and handles alarms and remote commands. It suits multiple sites or long pipelines. It needs reliable communications and attention to cybersecurity.

DCS and SIS

A DCS runs continuous process control for a whole plant, often with redundancy. A safety instrumented system is separate and acts only to bring the process to a safe state, under IEC 61511. We support migrations of both, including PVCII.

  • Skid and package control, such as LACT, injection and HPU skids
  • Wellsite, pad and facility monitoring
  • Pump, compressor and valve sequencing
  • Upgrade of obsolete control systems
  • Data to a control room or remote operations center
  • Savings in materials, labor and energy, with better quality, accuracy and precision
  • Process description and the equipment to be controlled
  • I/O list, with signal types and field voltages
  • Hazardous area classification and site conditions
  • Communication needs: protocols, existing PLC or SCADA, remote access
  • Existing system make and version, for a migration or integration

We define the architecture with you, program the logic and screens, build and test the system, and commission it in the field. For migrations we plan the cutover to limit downtime. We supply PLC, remote I/O, HMI and SCADA computers, and aim to be an ally rather than a traditional vendor: manufacturing solutions, automated electromechanical projects, technological support and integrator solutions.

BrandsYokogawa
02

Control panels

A control panel gathers the logic, power and operator interface for a piece of equipment in one enclosure. The right type depends on the available utilities, the area classification and how much the process needs to do.

Request a quote
Pneumatic control panel

Pneumatic

Logic and control done with air or gas pressure, with no electrical power. Works well for simple on/off and shutdown functions in hazardous or remote locations. Limited for complex logic, data and remote communication.

Electric

Relays, contactors, push buttons, lights and drives in a wired enclosure. Reliable and easy to understand for simple sequences and motor control. Changes mean rewiring, and the logic is hard to expand.

Hydraulic

Panels that control hydraulic power for actuators, using pumps, manifolds and accumulators. Used where high force or fail-safe spring return is needed, for example on large valves. Needs clean oil and regular checks on the fluid and seals.

PLC

A programmable controller with an operator interface and the field wiring inside. Handles complex logic, alarms, data logging and communications, and can change by editing the program. Needs a skilled programmer for changes.

  • Skid and package control
  • Valve and actuator control, including shutdown valves
  • Motor starting and protection
  • Burner, boiler and fuel systems
  • Hazardous area locations where compressed gas or air is the safer power source
  • What the panel must control and the sequence of operation
  • Power supply, voltage and available instrument air or gas
  • Area classification and ingress protection needed
  • Number and type of inputs and outputs
  • Interface needs: local screen, signals to your DCS or SCADA

Our engineers prepare the drawings and bill of materials, build the panel in our workshops, test it and commission it on site.

FAQ

Common questions

When should I choose a PLC over relays or a pneumatic panel?

Choose a PLC when you need alarms, data, remote communication, or logic you may change later. Relays and pneumatics are fine for simple, fixed functions, especially where power or skilled support is limited.

Can you take over a control system someone else built?

Often yes. We start by reviewing the drawings, program backups and hardware. If documentation is missing, we plan a site survey before quoting the work.

What is the difference between a DCS and a SIS?

The DCS controls the process in normal operation. The SIS is an independent layer that takes the process to a safe state when limits are exceeded. They are kept separate on purpose, so one failure does not disable both.

Do you help with factory and site acceptance tests?

Yes. We test the panel against the agreed functional description before delivery, and we commission it in the field with your operators.

Looking for a complete system?

See how we integrate these products into skids, built and tested in our workshops.

Get a quoteSkids